9126-0006 Zoll M Series Defibrillator Machine Parts Energy Discharge Capacitor

9126-0006 Zoll M Series Defibrillator Energy Discharge Capacitor
 
 
GENERAL MAINTENANCE
 
The resuscitation equipment must be maintained for immediate use. The following operational checks should be carried out at the beginning of each shift to ensure correct equipment operation and patient safety.
Refer to the corresponding operator shift checklist at the end of this section. Copy and distribute the appropriate forms to all individuals responsible for equipment use and preparation.
Note: Self-test defibrillation and pacing data will be automatically recorded on the PCMCIA data card (if any). The device can be configured to delete all self-test data from the data card when the power is off. For details, please refer to the M Series Configuration Guide.
an examination
Make sure that the equipment is clean (no liquid spills) and that nothing is stored on the equipment.
Make sure that two sets of MFE pads are provided in a sealed package. Check the expiration date on the packaging of all MFE Pads.
Check that the surface of the blade is clean and free of electrolyte gel and other contaminants.
Check that all cables, wires, and connectors are in good condition, are not cut or frayed, and have no bent pins.
Verify that all disposable supplies (electrode gel, monitoring electrodes, recording paper, alcohol swabs, razors, antiperspirants) are present and in proper condition.
Check if an empty memory card is installed in the device (if applicable).
Check whether a fully charged battery is installed in the device.
Check if the device has a fully charged backup battery.
 
 

 
Cleaning
M series products and their accessories are chemically resistant to the most common cleaning solutions and non-corrosive cleaning agents. The following list includes approved cleaning solutions;
• 90% isopropyl alcohol (except adapter and patient cable)
• Soap and water
• Chlorine bleach (30 ml/liter of water)
ZOLL recommends using a soft damp cloth and the above-mentioned cleaners to clean the equipment, blades and cables. The parts of the recorder can only be cleaned with a damp, soft cloth.
Do not immerse any part of the equipment (including paddles) in water. Do not use ketones (MEK, acetone, etc.). Avoid using abrasives (such as paper towels) on the display window. Do not disinfect the equipment. Special care should be taken to clean the defibrillation paddle after each use. The accumulation of gel can interfere with the monitoring of the paddle ECG (at first glance) and may cause an electric shock hazard to the operator. Keep the paddle handle clean.
Clean the recorder print head
To clean the recorder print head, do the following
pace:
1. Press and pull the tray drawer
The location of the RELEASE label.
2. Remove the paper (if necessary).
3. Pull the drawer completely out.
4. Tilt the device back so that the bottom of the drawer
It's easy to see.
5. Locate the plastic sheet on the back of the drawer.
6. Press the pull-down tab (beyond the plastic ridge) and pull out the drawer
Until removed.
7. Find the row of soft and thin bristles.
8. Find a thin black line (print head) and
Parallel to the bristles.
9. Gently wipe the thin black lines with alcohol
(Isopropyl) Wet the cotton swab. Dry any remaining alcohol
Comes with a new cotton swab.
10. Put the drawer and paper back in the machine.

 
Semi-automatic defibrillator test
If the "LOW BATTERY" message appears during the test at the start of the shift, the battery currently in use is about to run out and should be replaced and recharged.
The device does not test whether the battery has enough power to support the long-term use of the device, and can only determine the capacity by testing the battery in a suitable ZOLL battery charger.
1. Power-on sequence check
Connect the patient end of the multifunction cable to the defibrillator test connector.
Starting with the selector switch OFF, turn the selector switch to the ON position and observe the following:
• 4 beeps indicate that the POST has been successfully completed.
• Display and broadcast CHECK PADS or ATTACH PADS messages.
2. Defibrillator test
• Press the analysis button. The verification unit is charged to 30 joules (30J ready message).
• After the device is charged, make sure that the SHOCK button is lit.
• Press and hold the shock button.
• TEST OK should be displayed briefly on the screen and printed on the strip chart recorder (if available). These messages indicate that the energy provided by the device meets specifications.
• If "TEST FAILED" appears, please contact the corresponding technician or ZOLL technical service department immediately.
• Connect the multi-function cable to the ZOLL ECG simulator. Set the emulator to VF.
• Confirm that the "CHECK PATIENT" message is displayed and announced within 30 seconds.
• Press the analysis button. Verify that the device is charged to 200J (non-biPhilipilipase) or 120J (biPhilipilipase) or other pre-configured levels.
• After the device is charged, confirm that the SHOCK button is lit and the message "PRESS SHOCK" is displayed and announced.
• Press and hold the shock button. Verify that the device is discharged.
3. Recorder inspection (if applicable)
• Check if the paper supply is sufficient.
• Press the RECORDER button. The strip recorder will continue to run until the RECORDER button is pressed again.
• Press and hold the SIZE button for at least 2 seconds to generate a calibration pulse. As long as the SIZE button is kept pressed, the calibration pulse will always be displayed on the display. In addition, the amplitude of the calibration pulse is 1 mv, regardless of the SIZE setting.
• Check the uniformity and darkness of the recorder's waveform.
• Check the consistency of the annotation characters and the completeness of the words.
• Check the strip recorder speed by verifying that the calibration pulse is 2.5 ± ½ mm wide and 10 ± 1 mm high.
Manual defibrillator test
If the "LOW BATTERY" message appears during the test at the start of the shift, the battery currently in use is about to run out and should be replaced and recharged.
The device does not test whether the battery has enough power to support the long-term use of the device, and can only determine the capacity by testing the battery in a suitable ZOLL battery charger.
1. Power-on sequence check
Starting from the selector switch OFF, turn the selector switch to the MONITOR position and observe the following conditions:
• 4 beeps indicate that the power-on self-test has been completed
Completed successfully.
• The ECG size should be x1, and the word "MONITOR" should appear in the center of the display.
• "PADDLES" or "PADS" should be displayed in the upper right center of the display.
• If no ECG cable is connected to the simulator, the message "ECG LEAD OFF" will be displayed and the ECG display will be a dashed line instead of a solid line.
2. Energy delivery and shock button. Perform this check at the beginning of each shift using paddles or multi-function cable settings (described below) according to your situation.
Paddle setting
• Confirm that the adult propeller has been installed and pushed all the way into the bracket on the side of the M series equipment.
• Turn the selector switch to DEFIB.
• Set the defibrillator energy level to 30 joules.
• Press the CHARGE button on the apical handle.
• When the ready to charge prompt sounds, use the sternal plate or the defibrillator energy selection button on the front panel of the defibrillator to change the selected energy to 20 joules.
• The defibrillator will disarm by itself
• Use the sternal plate or the defibrillator energy selection button on the front panel of the defibrillator to change the selected energy back to 30 joules.
 
Multi-function cable setting
• The multi-function cable should be plugged into the device.
Make sure that the multi-function cable is not plugged into its test the connector.
• Switch the device to DEFIB and set the energy to 30 joules.
• Information "CHECK PADS" and "POOR PAD
CONTACT" will be displayed alternately.
• Plug the multi-function cable into its test connector.
• The message "DEFIB PAD SHORT" will be displayed.